Stainless Steel Coatings, Inc.
South Lancaster, MA 01561
Oct 31, 2005 STEEL IT® Low VOC Stainless Steel Coating is high solids, low VOC stainless steel epoxy system that complies fully with environmental regulations. System consists of barrier primer and 316L stainless steel finish that are durable and resistant to corrosive effects of oils, solvents, detergents, and salt water. Featuring metallic grey satin finish that will not chip, peel, or flake, they can be applied by brush, roller, and conventional and airless spray techniques.

Aremco Products, Inc.
Valley Cottage, NY 10989
Oct 28, 2005 Graphi-Coat(TM) 623 titanium diboride-based coating is 2-part, water-based, non-volatile material applied by brush, roller, or dip- or spray-processing. Formulated with respective weight and volume solids content of 78% and 58%, product offers coverage rate at 1 mil dry film thickness of 890 ft²/gal. Minimum dry film thickness of 2.5 mil is recommended. Once applied, coating is typically air set for 1-2 hr at ambient temperature then cured in-situ or in 10-15 min at 1,300°F.

Enviroline Group (IECC)
Pompano Beach, FL 33069
Oct 20, 2005 Enviroline 58HS enables users to hold surface preparation for up to 90 days while still meeting VOC requirements. Suited for application on interior or exterior steel, concrete, and masonry surfaces, high-solids product has less than 250 g/l VOCs. Applications include large tanks requiring surface preparation and situations where humid environments exist.

Cortec Corp.
St. Paul, MN 55110
Sep 30, 2005 Applied by spray during in-line coil processing, VpCI(TM)-329D provides water displacing protective film that eliminates corrosion from internal and external coil layers. Product combines Vapor Phase Corrosion Inhibition with anti-corrosion agents, enabling formulation of clean film with lubrication characteristics. For coils exposed to industrial atmospheres with pickling, anodizing, and galvanizing, VpCI(TM)-329D can inhibit corrosion for up to 1 year.

Aremco Products, Inc.
Valley Cottage, NY 10989
Sep 28, 2005 As single-part, water-based, inorganic-ceramic coating system, Cerama-Dip(TM) 538N electrically insulates high-power ceramic resistors in applications to 2,600°F. Odorless, non-outgassing product contains no VOCs and features volume resistivity of 109 ohm-cm and dielectric strength of 225 V/mil at room temperature. Curing is accomplished by air-drying at room temperature for 1-2 hr then step curing for 1 or 2 hr at 200°F and 350°F, respectively.

Chemline Inc.
St. Louis, MO 63103
Sep 28, 2005 Zero-VOC polyurethane coating, CHEMTHANE 4200PW, can be spray-applied in single coat directly to prepared steel, iron, or concrete substrate without any primers. Since product contains no solvents, there is no taste or odor transferred into water. With 1:1 plural component mix ratio, users can achieve film build of 15-70+ mils in single pass application. Coating features cure-to-touch time of 6-8 min as well as resistance to thermal shock damage.

Devcon
Danvers, MA 01923
Aug 30, 2005 Non-shrinking castable liquid, Cable Cast FR urethane encapsulates, insulates, and provides strain relief for electrical connectors and cables. Because it forms flexible jacket with abrasion, tear, and puncture resistance, it can also repair power cable jackets and insulation. Intended for potting aerospace inserts, clear-drying 5 Minute® Epoxy FR adhesive/encapsulant paste fills gaps and bonds rigid substrates such as metals, glass, ceramics, concrete, and wood.

ITW Automotive Finishing Group
Toledo, OH 43612
Aug 23, 2005 Designed for automotive exterior and interior cut-in applications, RPA-1 powder gun provides bell-like performance features such as uniform film build and transfer efficiency. It atomizes with no moving parts and simplifies automation controls while minimizing number of robots and atomizers. Simplified design eliminates rotating parts and eliminates defects caused from impact fusion.

Aremco Products, Inc.
Valley Cottage, NY 10989
Aug 12, 2005 Corr-Paintâ„¢ CP4080 provides single-part, silicone based, water-dispersible coating system that provides corrosion protection and color identification on aluminum and steel structures. Applied via pneumatic spray equipment, brush, or roller, product adheres to sandblasted, rusted, and marginally prepared metal surfaces. It dries at room temperature, and resultant color-stable coating is resistant to oxidation, UV light, humidity, and salt spray.

Aremco Products, Inc.
Valley Cottage, NY 10989
Aug 10, 2005 With ceramic-metallic formulation, Quartz-Coatâ„¢ 845 bonds to glass and quartz halogen lamps to reduce glare in various industries. Opaque blacktop coating is single-part, water-based, inorganic system pigmented with deep-black, temperature-stable filler that enables coating to absorb and evenly diffuse light at temperatures to 2,000°F. It is formulated to viscosity range of 400–700 cps and has solids content by volume of 42.0%. Post-cure finish is moisture-resistant.

Michelman Inc.
Cincinnati, OH 45236
Jul 29, 2005 Applied to slip or interleave sheets, water-based SofTak(TM) prevents slippage of small individual consumer or industrial goods, as well as palletized loads, boxes, and furniture. Expected angle of slide ranges from 30-45°, depending on application rate and substrate characteristics. SofTak is glueable with range of hot-melt or water-based cold-set adhesives and is print receptive. It is repulpable in both acid and alkaline systems.

Aremco Products, Inc.
Valley Cottage, NY 10989
Jul 27, 2005 Two-part, 99% alumina-filled Pyro-Paintâ„¢ 634-AL bonds, coats, and seals refractory fiber boards and other shapes. Product is resistant to wetting by most molten metals, optimizing erosion resistance of underlying structure. Mixed in 3:1 ratio, material has solids content of 76.8% by weight and 66.0% by volume, and viscosity range of 5,000–6,000 cps. Water-based formulation dries at room temperature in several hours and cures fully within 2 hours at 200°F.

Sherwin-Williams Co. c/o Ultimate Lead Systems
Berea, OH 44017
Jul 20, 2005 Suited for interior or exterior use, KEM 4000 High Solids Acrylic Alkyd Enamel provides high gloss and is VOC-compliant. For light service environments, product may be applied directly to steel without primer. Coating is ready to use with no mixing of additional components, and can be tinted to broad range of colors. KEM 4000 is suited for general metal applications including steel decking, doors, farm equipment, pipe and construction, and agricultural equipment.

Imagineering Finishing Technologies
South Bend, IN 46619
Jul 12, 2005 Lead- and Cadmium-Free Electroless Nickel surface finish is electroless nickel process yielding mirror bright nickel phosphorus alloy that offers corrosion resistance, uniformity of coverage, and repair and salvage capabilities. Trivalent Chromate Conversion Coating produces protective coating on pure aluminum, zinc, and anodic aluminum. It minimizes corrosion, provides bonding surface for paints, and appears faint blue to tan and iridescent.

MACtac, Technical Products Division
Stow, OH 44224 1888
Jul 06, 2005 MACdots coating system provides custom adhesive deposition in dot formation on liner for medical applications requiring direct skin contact over extended time periods. Each pressure sensitive adhesives (PSA) can be tailored for specific use in regards to breathability, application pattern, as well as size of dots and volume of adhesive deposited per dot for control of adhesion. Products employ rubber-based, hypoallergenic, skin-friendly adhesive.

Industrial Nanotech, Inc.
Naples, FL 34108
Jul 01, 2005 Water-based Nansulateâ„¢ High Heat provides insulation protection from temperatures ranging from -40 to +400°F while offering corrosion protection to underlying substrate. Applications include oil refineries, food-processing plants, and steam pipes and boilers in any industrial environment.

Industrial Nanotech, Inc.
Naples, FL 34108
Jul 01, 2005 Nansulateâ„¢ Translucent GP and PT can be applied with roller, paintbrush, or airless sprayer at low pressure, and can be painted over with water-based paint. Coatings do not lose their insulation value due to moisture, mold, or dust. Translucent color enables visual inspection of substrate, which is critical for equipment inspections required in many industries. Applications include maritime, petroleum refinery, and shipbuilding industries.

Master Bond, Inc.
Hackensack, NJ 07601
Jun 29, 2005 Single-component UV19LV bonds and seals clear films and sheets to other films, paper, and foil substrates. Uninhibited by air, 100% reactive, acrylic-based polymer composition does not emit any VOCs during cure. Mobile liquid has viscosity under 300 cps @ 75°F and cures in 10–15 sec using UV cure equipment in 365 nm range. With operating temperature range of -60 to +250°F, cured material features tensile strength over 800 psi and elongation over 80%.

GE Advanced Materials
Wilton, CT 06897
Jun 27, 2005 Cycoloy Engineered Filler Resin provides sparkle effect while helping to eliminate flow lines. Based on flame-retardant Cycoloy resin matrix, halogen-free product features UL94 VO and 5 Va ratings, as well as deflection temperature of 85°C. Resin offers range of surface finishes, from rough to silky and matte to glossy. Metallic effect is suited for electronic devices, personal care products, small appliances, and telecommunications devices.

Thermal Ceramics, Inc.
Augusta, GA 30903
Jun 24, 2005 With operating temperatures of 2,000 or 2,400°F, fiber-based Kaofil® grades feature smooth consistency and workability. Pumpable products are installed with piston and diaphragm pumping equipment and are suited for hot spot repair in utility boilers, HRSG units, and blast furnace stoves. Moldable grades are suited for repair or joint filling applications in ferrous, non-ferrous, and commercial markets. Both come in 1 and 5 gal pails as well as 11¾ and 40 oz tube cartridges.