ZRC Worldwide
Marshfield, MA 02050
Mar 29, 2006 Requiring minimal surface preparation, ZERO-VOC ZRC combines best features of organic and inorganic zincs, and is solvent-free. Environmentally friendly, one-coat system cleans up with water, is heat resistant to 1,200°F, and meets VOC standards in all 50 states.

Cotronics Corp.
Brooklyn, NY 11232
Mar 17, 2006 Packaged in dispensing cartridges, 450°F Instant Metal 7056AL forms solid metallic aluminum layer that adheres to smooth, rough, or porous surfaces as well as most plastics, metals, ceramics, glass, and wood. It cures in 4-8 min at room temperature without objectionable sulfur odors. Once cured, metallic composite is machinable with standard tools and can also be tapped, drilled, and threaded.

Chemline Inc.
St. Louis, MO 63103
Mar 16, 2006 Engineered for wood, plywood, particle board, and corrugated structures, 2-component CHEMTHANE 7035 consists of 100% solids elastomeric polyurea that cures in 6-8 sec. It is sprayed directly to prepared wooden substrate to form seamless, plastic barrier against abrasion, impact, and tearing. Product also hides seams and imperfections in prepared surface without excessive epoxy mastics, Bondo® application, or sanding.

Henkel Loctite Corporation
Rocky Hill, CT 06067
Mar 08, 2006 Formulated for use with CSP and BGA packages, Loctite® 3549 underfill protects solder joints against shock, drop, and vibration. Material has been tested to JEDEC drop test standards on 0.4 and 0.5 mm lead-free devices. Compatible with lead-free solder materials, underfill is completely reworkable and features a pot life of 14 days at room temperature and 7 days at 40°C processing temperature.

Chemline Inc.
St. Louis, MO 63103
Jan 31, 2006 Containing no solvents, CHEMTHANE 2261 100% solids, zero VOC, 2-component polyurethane coating can be air-sprayed directly in thicknesses from 40-60 mils without additional primer. It features Shore D hardness of 75 and cure time of less than 5 minutes at 77°F. Formulated to have balance between cold-temperatures and heat resistance, coating resists cracking and delamination while also providing microbe resistance.

Birchwood Casey
Eden Prairie, MN 55344 2138
Jan 31, 2006 With processing time of 25 min, TRU TEMP black oxide finishing system operates at 200°F, eliminating splattering and boilover hazards. Nonpolluting system is free of EPA regulated chemicals and uses mild solutions that prevent formation of red coatings and white salt leaching. Suitable for finishing tooling components such as toolholders, workholding, and turret press tooling, it can process small parts in bulk loads while larger tools can be finished on racks.

Lund International Corporation
Hudson, MA 01749
Jan 26, 2006 Able to be applied 2 ways with thicknesses from 0.002-0.100 in., BrazeCoat(TM) is low-porosity (less than 1%) hardfacing material with carbide densities up to 70% by volume embedded in metallic matrix. Metallurgically bonded to base metal, resulting coating can achieve over 65 Rockwell C hardness values to withstand abrasive wear in high-impact applications. Actual coating particles can be tungsten carbide, chromium carbide, or combination thereof.

Hacker Industries, Inc.
Newport Beach, CA 92660
Jan 25, 2006 Featuring built-in color identifier to comply with ASTM standards, Hacker TopCoat strengthens bond between Hacker floor underlayments and floor covering adhesives. Product serves to enhance surface of underlayments and prepares surface for application of finished floor coverings. Underlayments can receive coating of ASTM F 2419-compliant TopCoat soon after application, and finished floor coverings can be attached when underlayment is dry (7-10 days typ).

Friction Control Solutions, Ltd.
Tirat Hacarmel 39120  Israel
Jan 25, 2006 Super-Finishing produces low roughness while hardening metal surface using single mechanical process. Mechanical lapping process creates organic layer that bonds into metal surface through chemical reaction, affecting surface roughness average, mean roughness depth, amplitude, and bearing area curve. Environmentally friendly solution does not use hazardous waste materials and can be applied to cylindrical parts, flat surfaces, and various metals.

Rust-Oleum Corp.
Vernon Hills, IL 60061
Jan 18, 2006 Thermakrete(TM) urethane coating shields industrial floors against thermal shock in -10 to +240°F temperature range. Capable of seamlessly expanding and contracting to resist cracking, it withstands caustic washdowns, heavy traffic, abrasion, chemicals, and standing water contamination. Each 3-component kit cures in less than 72 hr without need for primer or sealers. Available in 3/16 or ¼ in. thicknesses, it can be used in USDA facilities based on FSIS Directive 11,000.4.

Electrolube (A division of HK Wentworth Ltd)
Swadlincote, Derbyshire DE11 0AN  United Kingdom
Jan 12, 2006 Water-based Aquacoat Plus eliminates need for extraction and other precautions required for application of solvent-based conformal coatings. Non-flammable, low-VOC product contains no isocyanates and can be soldered through without producing toxic gases. Based on polymeric materials, phenol-free product is non-corrosive to cadmium and zinc plate. It comes in 2 formulations: WBP as standard and WBPS (Sprayable) for use in selective film coating equipment.

International Paint Co.
Houston, TX 77210
Jan 05, 2006 Designed to meet needs of steel fabrication industry, Intershield single pack non-slip polymer coatings are pre-mixed with precise amount of aggregate for application directly from can. Solvent-based Intershield 584 suits fabricators not impacted by strict VOC regulations, while Intershield 584HS complies with VOC regulations. Water-based Intershield 571 ultra-low VOC solution is formulated in clear finish, while Intershield 818 has peelable formulation.

Aremco Products, Inc.
Valley Cottage, NY 10989
Jan 05, 2006 Single-part, aluminum-rich Corr-Paint(TM) CP2010 polymeric coating provides corrosion resistance on steel components exposed to oxidation and corrosive atmospheres to 400°F. It dries and cures at room temperature to hard, non-porous, abrasion-resistant surface. Product is resistant to hydrochloric, nitric, ethylene chloride, and sulfuric acids, and also survives salt fog, salt spray, and humidity testing of over 1,000 hr. Coverage rate in 1.0 mil dry film is 722 ft²/gal.

Cortec Corp.
St. Paul, MN 55110
Dec 22, 2005 Clean, Preserve and Protect (CPP) Program restores metal parts and equipment to operational specification, preventing disposal and subsequent replacement costs. Designed for use where sandblasting is not applicable, 3-step treatment system utilizes chemistries to remove corrosion from metal parts, clean parts, and preserve restored parts. Program is available in various systems, including environmentally friendly, biodegradable, and zero VOC processing.

Michelman Inc.
Cincinnati, OH 45236
Dec 20, 2005 Meeting requirements for non-scuff performance of corrugated shipping containers, Nomar(TM) Series coating eliminates abrasion that occurs between inside of shipping containers and packaged items while in-transit. Environmentally friendly product has water-based composition and is FDA-approved. Series withstands heat of corrugation, will not transfer onto packaged items, and can be glued with water-based and hot-melt adhesives.

Chemco Mfg. Co., Inc.
Northbrook, IL 60062 1920
Dec 07, 2005 Washable Coatings are offered in White and Clear Tacky versions for use in areas requiring dust control, while White and Clear Dry versions suit standard operating conditions. Available in bright white or clear, High Temperature Strippable Spray Booth Coatings are rated for all industrial bake oven style spray booths as well as curing ovens and other elevated-temperature applications. All coatings are water-based and may be applied using airless or pressurized spray equipment.

Anvil International, Inc.
Portsmouth, NH 03802
Dec 02, 2005 Resistant to wastewater, corrosive soils, hydrocarbons, harsh chemicals, brine, and saltwater, Scotchcote 134 fusion-bonded epoxy coating protects metal surfaces from corrosion. Corvel 1660, designed to protect inside diameters of tubular goods, is resistant to H₂S, CO2, harsh chemicals, brine, and saltwater. Specialty coatings, available upon request, include nickel coating, chrome plating, Teflon coating, Nap-Guard coating, and powder coating.

Cortec Corp.
St. Paul, MN 55110
Nov 08, 2005 CorrVerter(TM) surface prep lays foundation against corrosive intrusion in high humidity and salt atmospheres for rusted surfaces that will go back into service. Anti-corrosion barrier primer, VpCI(TM)-396 sets up adhesion for new steel and aluminum substrates. As thixotropic, water-based acrylic, VpCI(TM)-386 topcoat protects against electrolytes and aggressive marine environments. Combined, agents form self-healing monomolecular barrier within system to block corrosive attack.

Birchwood Casey
Eden Prairie, MN 55344 2138
Nov 03, 2005 Intended for large part finishing and in-place components, Antiquing Gels cling to vertical surfaces and stay where they are applied, without forming runs and drips or bleeding onto adjoining surfaces. After surface is cleaned using solvent cleaners or abrasive pads, user applies layer of antiquing Gel with synthetic paintbrush, allowing Gel to work for 2-10 min. When desired depth of black or brown tone is achieved, Gel is rinsed off with wet sponge and surface is dried.

Dylon Industries, Inc.
Cleveland, OH 44144
Nov 03, 2005 Water-based Grade AE, applied to metal, wood, concrete, plastic, glass, or ceramic surface, dries into smooth, non-porous graphite layer. Electrically and thermally conductive paint can be used as dry lubricant or as anti-stick agent in oxidizing environments to 500°C and in reducing or inert atmospheres to 3,000°C. Able to be removed by cold water, non-toxic product will not crack, run, or melt at any temperature and does not entrap dirt.