Composite Advantage
Dayton, OH 45420
Jun 18, 2008 FRP Pads and Mats offer corrosion resistant foundations and support surfaces that minimize amount of soil preparation required prior to starting development work. Providing portable access for heavy traffic or equipment to environmentally sensitive or challenging areas, lightweight, molded, and non-slip pads can be used as temporary roadways, helicopter landing pads, outrigger pads, trench plates, or supports for building relocation.

Enea
San Jose, CA 95134
Jun 18, 2008 Occupying as little as 8 KB of memory, OSEck (OSE Compact Kernel) is DSP-optimized RTOS that delivers preemptive, event-driven, real-time response and offers built-in error detection and handling. It is available in CEVA-TeakLite-III(TM) cores, which feature native 32-bit processing and dual Multiply-Accumulate (MAC) architecture. As scalable VLIW-SIMD DSP architecture with OSEck, multipurpose CEVA-X supports 2-16 MAC units with added computational resources and memory bandwidth.

APM-Hexseal Corp.
Englewood, NJ 07631
Jun 17, 2008 IQ(TM) (Installs Quickly) environmental switch and circuit breaker silicone sealing boots have integral bonded concentric aluminum nut that screws directly onto, and completely surrounds, existing front-panel switch bushing-nut. Products have round base and provide protection to IP 66/68 against hostile contaminants that can invade and corrode internal contacts. Conforming toggle design fits switches/breakers with 15/32-32 bushing, requiring 0.975 in. boot height.

Schaeffler Group USA, Inc.
Fort Mill, SC 29715
Jun 12, 2008 To optimize vibration damping, LuK Dual Mass Flywheel features centrifugal pendulum-type absorber mounted on flange. Stiffness of pendulum is generated by centrifugal force during operation. Absorber has no set natural frequency, causing frequency to change depending on speed. Pendulum mass of 2.2 lb can reduce transmission vibrations up to 60%. Designed to optimize driving comfort, dual mass flywheel will last for entire service life of vehicle.

ASG, Div. of Jergens, Inc.
Cleveland, OH 44110
Jun 10, 2008 Suited for vertical screw applications, Linear Torque Arm has linear slide that offers smooth motion for electric or pneumatic inline tools. Machined stainless steel and multiple ball bearing design with side-by-side slides provides stability for horizontal extension and retraction of tools up to 5 lb in weight and up to 150 lbf-in. torque. Arm movement is up/down, in/out, and full 360º radial side-to-side. Each arm is provided with 2 ASG 1-3 lb spring balancers.

Elma Electronic Inc.
Fremont, CA 94538
Jun 02, 2008 Suited for commercial and military aviation, ARINC 404A Full-Size ATR Long Enclosure features modified front panels that can be secured to chassis, optimizing protection for shock and vibration. Shock absorbers/dampers can also be added to enclosure for extra protection, and thermal management can be achieved via convection or conduction cooling. Testing shows chassis meets MIL-STD-810E shock/vibration requirements and MIL-STD-461 for electromagnetic interference.

Bosch Rexroth Corp., Linear Motion & Assembly Technologies Div.
Charlotte, NC 28273
May 28, 2008 Offered as environmentally friendly alternative in applications that traditionally use hydraulic or pneumatic cylinders, variety of Electromechanical (EMC) Cylinders gives users custom control over required positioning accuracy, axial thrust power, torque, and speed. Products, rated to IP65, offer corrosion-resistant construction and incorporate precision-rolled ball screw actuator. Offered in 6 sizes, cylinders offer stroke lengths to 2,000 mm and speeds to 1.6 m/sec.

Lanxess - Technical Rubber Products
Pittsburgh, PA 15275
May 16, 2008 THERBAN® C 3669 VP (36% ACN; 6% RDB; 95 Mooney viscosity) is offered as alternative to acrylonitrile-butadiene copolymers (NBR) rollers in fabrication of rubber roll coverings used in extreme environments. Soft printing roll cover option, made of THERBAN hydrogenated acrylonitrile-butadiene copolymer (HNBR), allows for development of compound formulation with high acceptance of plasticizer. It also contributes to symmetrical shape during roll cover fabrication.

Safety Technology International, Inc.
Waterford, MI 48327
May 14, 2008 Constructed of aluminum with moisture resistant cord grips for cable penetration, Stopper® Line housings protect cameras from harsh indoor/outdoor environments as well as physical abuse and accidental damage to help stop false fire alarms, vandalism, and theft of fire/security equipment. Including STI-7000K basic unit and STI-7100K with heater, blower, and sunshield, they have spring assisted forward opening lid, rear link-lock latch, and mounting bracket.

ITT Corporation
White Plains, NY 10604
May 09, 2008 D-subminiature connectors meet requirements for corrosion resistance under MIL-Spec P grade stainless steel as well as JEDEC standards for RoHS compliance. Available in sizes E, A, B, C and D, including 9-50 contact patterns in standard sizes and 15-78 contact patterns in high density sizes with 40 A max current/contact, stainless steel shells are suited for variety of applications including telecommunications, marine, aerospace, petrochemical, and pharmaceutical.

Stafford Mfg. Corp.
Wilmington, MA 01887
May 02, 2008 Available with plain and tapped holes, Accu-Flange(TM) Collars and Precision Sleeve Flange Couplings enable user to attach components such as pulleys and cams. Collars are machineable and couplings have solid center section for close tolerance fit on ground shafting. Supplied with standard keyway, both are available with ½-1 ½ in. bores in SS, steel, and aluminum and will not mar shafts. Collars retain perpendicularity and couplings maintain less than .001 TIR concentricity.

Whittet-Higgins Co.
Central Falls, RI 02863
May 02, 2008 Offered in aluminum, stainless steel, and carbon steel, threaded retaining ClampNuts are available with AFBMA/ANSI, American National, ISO, Metric, Unified Coarse, Unified Fine, and Unified Constant options. Bore sizes range from 1/8-7¾ in. and 10-200 mm. Plain bore clamp style and split collars, also available, come in 1/8-4 in. and 3-100 mm bore sizes. ClampNuts and collars minimize installation and maintenance times and eliminate cutting keyways and shaft marring.

Marvell Semiconductor Inc.
Santa Clara, CA 95054
May 01, 2008 Discovery(TM) Innovation Series is comprised of 3 devices - MV78200, MV78100, MV76100 - that integrate single- or dual-core, gigahertz-capable, ARM instruction set-compliant processors along with I/O peripherals. They support processor speeds from 800 MHz to 1.2 GHz and incorporate up to 512 KB L2 cache per core. Additional features include x4 PCI-Express(TM) interfaces, multiple USB 2.0 ports, multiple Gigabit Ethernet ports, SATA, and security engine.

Synopsys, Inc.
Mountain View, CA 94043 4033
May 01, 2008 DesignWare PHY IP for PCI Express 2.0 (Gen II) provides designers with complete, silicon-proven PCI Express 2.0 IP solution that includes digital controllers, PHY, and verification IP. Accessing all IP from one provider helps lower risk of integrating 5.0 Gbps PCI Express interface into SoC designs. Along with diagnostic capabilities and ATE test vectors for at-speed production testing of PHY, solution offers backwards compatibility with PCI Express 1.1 and PIPE specifications.

Stafford Manufacturing Corporation
North Reading, MA 01864-0277
Apr 30, 2008 Stafford Hinged Shaft Collars feature triple-link hinge and captive clamping screw to simplify assembly. Offered with round, threaded, hex, and square bores, they are suitable for use as stops or spacers and for mounting devices in applications involving different shaft configurations. Collars are available in 25 sizes from 3/8-4 in. ID and 16 metric sizes from 6-50 mm and are offered in steel, SS with stainless clamping screws, and aluminum.

H & S Tool, Inc.
Wadsworth, OH 44281
Apr 29, 2008 Powered by pneumatic motor, BF portable flange-reconditioning tool is able to apply 3 different surface finishes from 63-250 RMS with automatic feed. It has working range of ¾ ID to 8 in. OD with which to square and refinish flange faces and bolt hole patterns. Tight-clearance package, available for working in areas as small as 2¾ in., offers max working reach of 5½ in. Tool securely locks in ID of tube and is self-centering.

ConProTec Inc.
Salem, NH 03079 2060
Apr 29, 2008 Available in volumes from 75-1,500 mL with ratios of 1:1, 2:1, and 10:1, cartridges are offered in polypropylene and nylon to meet requirements of chemistries used in construction industry applications. Peeler Cartridge lets users package 2-component material in one cartridge that fits standard caulking guns. Also available, static mixer models range from traditional helical style to square Quadro design. Disposable static mixers are also available.

Metallized Carbon Corp.
Ossining, NY 10562
Apr 28, 2008 Metcar® Grade M-400, CS Series Blanks for general duty applications and Metcar® Grade M-106, HS Series Blanks for high-load, high-speed applications are machineable with conventional tungsten carbide or diamond tools. Suited for machining mechanical seal rings, bearings, and vanes, blanks offer lubrication when running in low viscosity liquids from -400 to +500°F.

Ideal Shield, LLC
Detroit, MI 48209
Apr 28, 2008 Manufactured from polyethylene thermoplastic, Ideal Shield® Bumper Post Sleeve slides over existing steel post to eliminate need for maintenance. It is available for post diameters ranging from 3-10 in., with sleeve height available up to 84 in. Delivered with installation tape, sleeve is available in a variety of colors and can be customized with molded in company logo.

80/20, Inc.
Columbia City, IN 46725
Apr 25, 2008 Made of lacquer-finished die-cast aluminum, Corner Connectors are available in 2-way and 3-way versions for 30, 40 and 45 Series T-slotted aluminum profiles. Color matched push-in plastic cover caps are supplied to give frames clean, finished appearance. Profile ends are tapped to accept button head socket cap screws used for connector's assembly.