Walton Plastics, Inc.
Walton Hills, OH 44146
Jul 31, 2008 Exhibiting chemical resistance and temperature flexibility, Flexible Polyurethanes (TPUs) are available in polyether-, polyester-, and aliphatic-based versions to match specific film and sheet requirements. Specialty grade polyurethanes are also available, including halogenated and non-halogenated fire retardant, static dissipative, as well as versions certified to NSF, FDA, and European standards. Material ranges from 70 Shore A to 60 Shore D and .030-.250 in. thick.

Objet Geometries Inc.
Billerica, MA 01821
Jul 31, 2008 Addressing broad range of applications, DurusWhite FullCure430 gives same milky-white look and feel of final products made of polypropylene. It simulates toughness (Izod notched impact of 44.22 J/m), flexibility (elongation at break of 44.2%) and strength (modulus of elasticity of 1,135 MPa) of polypropylene. Available in environmental friendly, sealed 3.6 kg cartridges, DurusWhite works with Connex500, Eden500V, Eden350V, Eden350, and Eden330/333 3D printing systems.

Trans Tech America, Inc., An ITW Decorating Co.
Carol Stream, IL 60188
Jul 30, 2008 Suited for use in medical applications, Type 434 ink offers high opacity and adhesion to both untreated and pretreated polypropylene substrates. Ink features fast drying single component and offers fast start-up, especially in rotary applications. High gloss ink is available in both black and white.

Air Products & Chemicals, Inc.
Allentown, PA 18195
Jul 29, 2008 XeCovery^SM On-site Xenon Recovery System is service that allows semiconductor manufacturers to recover and reuse xenon gas. Based on technology utilizing Vacuum Swing Adsorption, process is capable of extracting xenon from process effluent streams. Enriched mixture of recovered xenon, typically in percent levels, is compressed and stored. Full vessels are then transported off site for distillation.

CoorsTek
Golden, CO 80403
Jul 29, 2008 PlasmaPure(TM)-UC Alumina offers extreme purity (99.9%) critical for semiconductor, electronic, and optical industries. Able to extend component life and reduce contamination, ultra-high-purity ceramic material exhibits etch resistance in corrosive chemistries, minimal sodium content, and dielectric loss tangent under 0.00002. Fine-grained material also exhibits corrosion resistance and minimal sodium content.

Kimball-Midwest
Columbus, OH 43228
Jul 28, 2008 Protecting materials by reducing heat transfer during soldering, brazing, welding, and open flame contact, Therma-Shield Heat Protection Paste eliminates disassembly of valves and other components. It can be applied to almost any surface or material, and conforms to irregular shapes and surfaces to provide total coverage and protection. Product is non-flammable, non-toxic, non-corrosive, and biodegradable, and helps eliminate waste as it can be applied only where needed.

Philadelphia Mixing Solutions
Palmyra, PA 17078 9518
Jul 28, 2008 Designed for mixing heavy-duty concentrations of water and wastewater, RAVEN(TM) 3800 Series can be used in caustic and corrosive environments. It features cast-iron housing with open tank mounting configurations, input and intermediate shaft designs for reduced deflections, C-Face motors with piloted motor adapters, dry wells, and end covers. With drive-sleeve design, unit comes in double and triple reductions from 4:1 to 130:1 overall gear ratios to accommodate various requirements.

PB Swiss Tools
Gainesville, GA 30501
Jul 25, 2008 With soft handle surface that ensures secure grip even if hands are wet, SwissGrip® screwdrivers transfer rotational forces of the hand to screw, maximizing torque. Compact 8215 ESD Screwdriver Set includes ESD handle and precision screwdrivers. Designed to check screw tightening torques for assembly operations, 8315A ESD Torque® Handles come with preset torque setting range of 10 cNm to 5 Nm, which can be adjusted according to specific requirements.

Soitec, Inc.
Peabody, MA 01960
Jul 25, 2008 Fabricated using Smart Cut(TM) process, ultra-thin top silicon and ultra-thin Buried Oxide meet advanced requirements in terms of defectivity, flatness, and silicon-on insulator thickness control of up to ±10 Angstroms. Top silicon layer of wafers is available in thicknesses ranging from 20-110 nm, while BOX can be as thin as 10 nm. Substrates are suited for partially depleted and fully depleted devices, including multi-gate transistor architectures.

Misumi USA
Schaumburg, IL 60173
Jul 22, 2008 Suited for building of machinery and equipment, Urethane, Rubber, and Sponge Components come in round and metal plate-mounted versions as well as configurable block versions. Urethane and rubber bumpers feature round tips, and come in choice of solid or through-hole designs. With diameters, lengths, and through-hole sizes configurable in 1 mm increments, hundreds of sizes and shapes are available. Urethane blocks mounted on metal plates are offered in flat, V-shaped, and corrugated designs.

Stedman
Aurora, IN 47001
Jul 21, 2008 With optimal hydraulic drive system that offers variable mill speeds, Model VS-88 V-Slam(TM) Vertical Shaft Impactor features speeds of up to 12,500 fpm and capacity range of 5-500 tons/hr. Offering high operating speed for fine grinding, it has low profile split swing lid, indexing feed tube and anvil ring, and automatic recirculating lubrication system. Applications include minerals and ores, slag, bottom boiler ash, flux, alloys, glass, chemicals, magnesite, corn, salt, and coke.

Turbex Ltd
Alton   United Kingdom
Jul 18, 2008 Suited for use in repair and maintenance shops serving transport depots, railyards, and marine workshops, AS-150 has load capacity of 800 kg, and can accommodate components measuring 900 mm high by 1.4 m across diagonal or diameter. It uses detergent cleaning medium dissolved in water heated to 50-75ºC, delivered at 400 Lpm, and 4 bar pressure through rotating spray pipes. Model AS-100 is suited for cleaning components up to 950 x 700 mm and weighing maximum ½ ton.

Schulman, A. Inc.
Akron, OH 44309
Jul 18, 2008 Invision PX modified polypropylene-capped TPO (thermoplastic olefin) sheet and Invision TX mono-layered TPO sheet offer high melt strength allowing for large process window, for processing flexibility. They also provide high stiffness which enables processors to down-gauge.

Brewer Science, Inc.
Rolla, MO 65401
Jul 17, 2008 Exhibiting bonded pair rigidity and thermal stability, Brewer Science WaferBOND(TM) HT-10.10 bonds fragile device wafers to rigid carriers to allow thinning and subsequent processing to create through-silicon vias (TSVs). This spin-on polymeric temporary wafer bonding material is resistant to solvents, acids, and bases. Device structure planarization with total thickness variation of less than 0.5 µm on 10 µm coating permits thinning to 50 µm and beyond.

Spectronics Corp.
Westbury, NY 11590
Jul 15, 2008 Formulated specifically for large industrial systems, oil-based OIL-GLO(TM) 40 pinpoints leaks in all synthetic- or petroleum-based fluid systems, including light-colored hydraulic fluid, very dark or intensely blue hydraulic and lubrication fluids, compressor oil, engine oil, and gearbox oil. Product can remain safely in system for periodic re-checks, eliminating need to add more dye until oil is changed.

Graymills Corporation
Chicago, IL 60613
Jul 15, 2008 Model PH822-A environmentally minded, solvent-free parts washer offers electrical control interface to provide complete machine status to operator. Unit features flow-thru work brush, flexible stay put nozzle, adjustable thermostat, 300 gph pump, GFCI protection, and triple-action filtration. Washer is 4-legged, and comes with sink and stainless steel work shelf which can be removed to expose 10 in. deep soak area.

Simrit, A Div. Of Freudenberg-NOK
Plymouth, MI 48170
Jul 15, 2008 With service temperature of -6 to 300°C, Simriz® 508 exhibits plasma resistance and minimum particulation in range of plasma environments. White perfluoroelastomer material is designed for thermal stability and nearly universal protection against chemical attack. Suited for deposition, oxide, and metal plasma etching, ashing, metallization, and ion implant, product is appropriate for chamber lid seals, bell jar seals, endpoint windows, gas inlet seals, and isolator valve seals.

E. F. Bavis & Associates, Inc.
Maineville, OH 45039
Jul 15, 2008 Designed to replace pneumatic tube systems used in drive-thru service lanes at banks, TransTrax® uses less than 1/10th electricity, has only 4 moving parts, and is constructed of recyclable materials, most of which are aluminum. By using positive drive system and smart sensors, single motor operates only when needed to deliver carrier. TransTrax delivers to 2 vehicle heights and is unaffected by weather conditions.

NOVOMER, INC.
Ithaca, NY 14850
Jul 15, 2008 Suited for electronics and ceramics manufacturing, NB-180 PPC degrades completely and uniformly into environmentally benign products, providing mechanical strength to ensure consistency, solidification, or adhesion. Amorphous, colorless thermoplastic polymer produces ash residues less than 5 ppm. Based on 3% binder use levels, residual ash levels in finished parts are less than 1 ppm. NB-180 can be produced in customized viscosities and molecular weights to meet specific requirements.

Tyco Electronics Corp.
Harrisburg, PA 17105-3608
Jul 14, 2008 Resistant to nuclear, chemical, and biological (NBC) threats, Thermorad 700 Series NBCCS fluoroelastomers are suited for cable jackets and wire insulation in applications requiring NBC contamination survivability (NBCCS). Grades are available to cover -55 to +125°C (Thermorad 770), -55 to +175°C (Thermorad 780), and -65 to +200°C (Thermorad 790) temperature ranges and are offered as option in custom multi-core cabling products. Each grade is thoroughly tested.