Pres-On Products, Inc.
Addison, IL 60101
Jul 30, 2008 Coated on one-side with long-aging, high-tack acrylic adhesive, Pres-On® U6000 tape is suited for use in OEM product applications where gasketing, cushioning, and recovery is required. Two-sided U6200 can also be used in assembly applications as well as for secure mounting. Uniform cell structure allows application to clean, dry materials. While cushioning characteristics isolate vibrations, absorbent property traps moisture, light, dust, and contaminants.

Henkel
Rocky Hill, CT 06067
Jul 30, 2008 Loctite® 5510(TM) and Loctite 5570(TM) are primerless, one-component, odorless adhesives that cure by reacting with ambient moisture and achieve functional strength in 24 hr. Available in white, grey, or black, Loctite 5510 bonds and seals simultaneously, fills gaps, resists weather and moisture, and withstands ongoing shock/impact. Available in clear or white, Loctite 5570 replaces mechanical fasteners and rivets while also providing vibration- and sound-dampening benefits.

Kimball-Midwest
Columbus, OH 43228
Jul 28, 2008 Protecting materials by reducing heat transfer during soldering, brazing, welding, and open flame contact, Therma-Shield Heat Protection Paste eliminates disassembly of valves and other components. It can be applied to almost any surface or material, and conforms to irregular shapes and surfaces to provide total coverage and protection. Product is non-flammable, non-toxic, non-corrosive, and biodegradable, and helps eliminate waste as it can be applied only where needed.

Wacker Chemical Corp.
Adrian, MI 49221
Jul 28, 2008 Available in 1- and 2-component systems based on polyorganosiloxanes, SEMICOSIL® UV Elastomers cure at room temperatures within minutes. Curing rate can be controlled by appropriate selection of elastomer, UV dose, and process temperatures. Product generates no by-products during curing, making it suited for encapsulation of electronic components.

International Tape Co.
Windham, NH 03087
Jul 28, 2008 Optimized for strength, Product 207PXL consists of lightweight tissue coated on both sides with high-tack, dead load synthetic-based adhesive system. It has easy-release polysilicone liner and is recommended for applications that require bonding of medium- to heavy-weight pieces of advertising, displays, forms, and chipboard boxes. Solution is also suited for splicing because hand pressure is sufficient for transfer to most webs, after which liner can be removed.

Henkel Loctite Corporation
Rocky Hill, CT 06067
Jul 25, 2008 Suited for threaded assemblies that are continuously exposed to extreme temperatures, medium-strength Loctite® 2422(TM) is designed for applications where disassembly with hand tools is desired, while high-strength Loctite® 2620(TM) requires short-term exposure to temperatures over 650°F to remove nut and bolt with hand tools. Both pastes solidify when confined between close-fitting metal surfaces in absence of air, prevent loosening from shock and vibration, and eliminate leakage.

International Tape Co.
Windham, NH 03087
Jul 23, 2008 Double coated polypropylene and double coated paper tape products feature thick mass of aggressive adhesive that provides instant bond when applied to difficult surfaces, including low surface energy films. Various substrates can be coated on both sides, and additional substrates can be custom-coated upon request. Used in demanding applications, products are suited for bonding dissimilar or irregular surfaces.

Henkel Corp.
Madison Heights, MI 48071
Jul 21, 2008 Structural adhesives for metal/plastic bonding, threadlockers, thread sealants, seam sealants, and general-purpose adhesives are designed for micro- to large-size, stationary or portable fuel cell applications. Resistant to acids, coolants, and chemicals, these products are formulated to deliver gas-tight seal on components and stacks. Membrane electrode assembly (MEA) adhesives and sealants bond bipolar plates, seal MEAs, and seal between bipolar plates and end plates.

Brewer Science, Inc.
Rolla, MO 65401
Jul 17, 2008 Exhibiting bonded pair rigidity and thermal stability, Brewer Science WaferBOND(TM) HT-10.10 bonds fragile device wafers to rigid carriers to allow thinning and subsequent processing to create through-silicon vias (TSVs). This spin-on polymeric temporary wafer bonding material is resistant to solvents, acids, and bases. Device structure planarization with total thickness variation of less than 0.5 µm on 10 µm coating permits thinning to 50 µm and beyond.

Chemline Inc.
St. Louis, MO 63103
Jul 14, 2008 With mix ratio of 4A:1B, Monomid(TM) Epoxy Flooring System forms cleanable, high-gloss finish. It offers 5 mils DFT in one coat when applied over Monomid Clear Sealer and can be applied over various other primers for application on steel. Solution supports addition of anti-slip aggregate or sand and also offers moisture resistance. In 3 hr at 77ºF, coating dries to touch to form abrasion- and chemical-resistant finish. Use is suited for industries requiring low odor and VOC levels.

Aremco Products, Inc.
Valley Cottage, NY 10989
Jul 09, 2008 Ceramabond(TM) 685N is single part, dispensable, zirconium silicate based adhesive and sealant system that is used to bond ceramic honeycombs to metal frames used in construction of gas-fired ceramic radiant heaters. Thixotropic, water-dispersible, and fast-setting paste contains no asbestos or VOCs, and exhibits tensile-shear strength of 500 psi and linear shrinkage of less than 2% after curing. It is available in pint, quart, gallon, and 5 gal pails.

Huntsman Corp.
The Woodlands, TX 77380
Jul 09, 2008 Semi-flexible, cycloaliphatic epoxy material Araldite® S-HCEP is designed for producing sheds on reinforced fiber-core composite insulators used in medium- to high-voltage outdoor power applications. It exhibits intrinsic hydrophobicity, hydrophobicity transfer, and recovery. Requiring no stirring, degassing, or pre-heating, erosion resistant epoxy has 1:1 mix ratio by volume, permitting meter-mixing on same type of equipment used for liquid silicone rubber.

Master Bond, Inc.
Hackensack, NJ 07601
Jul 07, 2008 Formulated to cure at room temperature, 2-component Supreme 11AOHT can be applied without sagging or dripping. It has mixing ratio of 1:1, operating temperature of -100 to +400°F, thermal conductivity of 10 BTU/in/ft²/hr/°F, and dielectric strength of greater than 400 V/mil. Suited for applications involving thermal cycling, product adheres to most metals, ceramics, glass, rubbers, and plastics. Bonds are resistant to water, oil, and most organic solvents.

Master Bond, Inc.
Hackensack, NJ 07601
Jun 26, 2008 Formulated for general purpose bonding, Type EP50-1 produces high strength bonds with more than 2,000 psi at room temperature that are resistant to thermal cycling and chemicals including water, oil, and organic solvents. Suited for metals, glass, ceramics, wood, and vulcanized rubbers, product is approved for service over temperature range of -60 to more than 250°F. It comes in premeasured, flexible divider pouches, disposable cartridges, and in pint, quart, gallon, and 5 gal containers.

Master Bond, Inc.
Hackensack, NJ 07601
Jun 25, 2008 With 2.2 Btu-in./hr/ft²/°F thermal conductivity, Master Sil 150 is 2-part, condensation cured liquid silicone system which can be used for potting and encapsulation. It features Shore A hardness of 40, 230% elongation at break, 11 x 10^-4 cm/cm°C thermal expansion, and less than 0.4% linear shrinkage. Able to protect sensitive electronic components/assemblies from dust, moisture, ozone, thermal shock, and vibration, product cures in contact with virtually all types of materials.

Henkel Loctite Corporation
Rocky Hill, CT 06067
Jun 20, 2008 Designed to replace sticky cavity packaging and associated plastic waste, select Technomelt® Adhesives come in packets that load directly into dispensing tank where packet's dry outer casing melts with adhesive. Available in EVA, polyolefin, and pressure sensitive technologies, adhesives are used to manufacture filters, packaging, pressure sensitive adhesive films, insulation, textiles, vehicles, and structures.

Master Bond, Inc.
Hackensack, NJ 07601
Jun 19, 2008 Formulated to produce bonds with shear as high as 2,800 psi, MB297 is supplied as viscous liquid adhesive with viscosity of 2,000-2,400 cps at 20°C. Colorless solution, resistant to effects of extreme humidity, has refractive index of 1.48 and service operating temperature range of -65 to 185°F. Cures are moisture activated, and bonds are instantaneously formed with glass, metals, ceramics, plastics, and elastomers. Shore A hardness is 85.

National Adhesives
Bridgewater, NJ 08807
Jun 13, 2008 VelocityP3(TM) 33-711A and 33-711B multi-purpose non-contact extrusion adhesives provide fiber-tearing bonds on all substrates. Type 33-711A offers high pressure of 600 cps, while Type 33-711B offers low pressure of 300 cps. Solvent free, low-VOC adhesives have above average heat and cold resistance, and support machining, allowing clean cut-off and restart recovery. They are compatible with extrusion systems from Bobst, HHS, Valco, Nordson, and Pafra.

Scapa Medical
Inglewood, CA 90302
Jun 09, 2008 Products in Electrofix line are single-coated with medical grade acrylic adhesives in varying tacks and remove easily without leaving residue. They are supplied on range of flexible and conformable foam, film, non-woven, and laminate backings with heavy-duty glassine release liners. Dimensionally-stable and suitable for high speed conversion and die-cutting, products are available in white finishes or as clear polyethylene films. Other colors, including tan, are available on request.

MAG Industrial Automation Systems
Sterling Heights,, MI 48313
Jun 09, 2008 Designed for aircraft/aerospace industry, CHARGER(TM) Series of automated small flat tape layers with bed-type configuration are used in production of long narrow flat parts, nested multi-part laminates, and drape-formed skins. Enabling transition from metal to composite structures and from hand lay-up to automated tape lay-up, it features CM100 computer control. Tape layer produces laminates up to 47 in. wide on standard width machine and up to 100 in. wide on wide version platform.